Help me choose Please

[joes03cobra10thann]

I cann't decide what my next mod should be and every time I think that I made my decision I change my mind. (Im only buying one this week)

Possible mods:
1. MAF Sensor with knn could air intake
2. JLT cold air intake kit
3. afco heat exchanger
4. accufab throttle body

I cann't make up my mind!

Click to read more...

 

[VenomInside]

I cann't decide what my next mod should be and every time I think that I made my decision I change my mind. (Im only buying one this week)

Possible mods:
1. MAF Sensor with knn could air intake
2. JLT cold air intake kit
3. afco heat exchanger
4. accufab throttle body

I cann't make up my mind!

What are your mods again?

JLT, and heat exchanger.. you dont need the throttle body and you dont need the maf yet.

I would do the following if i was you..

Intake [JLT or K&N]
Exhaust [I love my bassani] w/ x-pipe
Pulley- Billetflow 2.93 or 2.76
Tune with SCT Xcal.
Heat Exchanger would be good..

But you dont need the TB [But if you do, do the pulley.. you might need a maf, depends on where you are at etc]

 

[joes03cobra10thann]

What are your mods again?

JLT, and heat exchanger.. you dont need the throttle body and you dont need the maf yet.

I would do the following if i was you..

Intake [JLT or K&N]
Exhaust [I love my bassani] w/ x-pipe
Pulley- Billetflow 2.93 or 2.76
Tune with SCT Xcal.
Heat Exchanger would be good..

But you dont need the TB [But if you do, do the pulley.. you might need a maf, depends on where you are at etc]

My only mods so far are magniflow offroad x pipe and magniflow cat-back.
So which should I do first afco heat exchanger or jlt-knn cold air kit?

 

[Wiked03]

My only mods so far are magniflow offroad x pipe and magniflow cat-back.
So which should I do first afco heat exchanger or jlt-knn cold air kit?

I would do a cold air before a heat exchanger. Leave the stock MAF until you are closer to maxing it out.


**Moved to tech

 

[Boost12]

You wont need a MAF for a while until you get in the high 400whp stages and theres no need for the throttle body in my opinion. I would do a nice pulley setup on the car and a good tune if I was you :biggthump And if you go with an Intake go with a JLT

 

[Flyn]

Do the CAI. Then maybe a pulley and tune after that.

 

[VenomInside]

Do the CAI. Then maybe a pulley and tune after that.

:ditto: trust me.. you'll be happy :headbang:

 

[apollyon]

Do the cold air intake. If you want to see what the JLT looks like pm me since you work right by my house.

 

[hj16]

Possible mods:
1. MAF Sensor with knn could air intake
2. JLT cold air intake kit
3. afco heat exchanger
4. accufab throttle body

I cann't make up my mind!

JLT, the rest are all wastes of money for you right now

 

[CobraSusie]

I cann't decide what my next mod should be and every time I think that I made my decision I change my mind. (Im only buying one this week)

Possible mods:
1. MAF Sensor with knn could air intake
2. JLT cold air intake kit
3. afco heat exchanger
4. accufab throttle body

I cann't make up my mind!

1. MAF Sensor with K&N cold air intake

 

[Flatliner]

Okay... I have JLT as well and that would be the route Iwould go.

On another note all recommending JLT anyone use RAI and have issues with clamp on RAI?

 

[Mr. Unknown]

My vote goes for the H/E keep it cool. :cool2:

 

[hj16]

My vote goes for the H/E keep it cool. :cool2:

A HE is not a cooling mod