🔧 BUILD toyota wagon 3800

[Turbocharged400sbc]

finished PS mount, i might clock the pump up more but it looks good, you can also make out some of the ICM to bellhousing mount to the right.
im going to bed, gotta run to the junkyard tomorrow with jamie (jbigalow) to rape and pillage a couple mustangs

 

[10sec]

Grab a monte carlo brake booster for me pleeeeeeeeaaaaseee :smile:

 

[Turbocharged400sbc]

why? your stock GTP pieces of shit are fine

 

[10sec]

Running a 3" dp on my blue car

 

[Turbocharged400sbc]

ill see if jamie will loan me the dough... when can ya pick it up?

ill check the price list inthe garage tomorrow morning but it shouldnt be more than 35-40$

 

[10sec]

Whenever, but it'll definitely get bought, i can promise you that.

 

[Turbocharged400sbc]

in a couple weeks or a few months?

 

[10sec]

Couple weeks, probably next secret meet

 

[Turbocharged400sbc]

ok, ill see what i can do, otherwise it was gonna wait for better weather lol

 

[10sec]

ohhh, in that case, just wait for better weather. I don't NEED it now. Yea, f-that, it's too damn cold. We'll go together when it's warmer out and you can show me the ropes.

 

[Turbocharged400sbc]

its just a clip and pin under the dash and two prybars from the engine compartment side after the master is taken off

 

[Handsome Jesus]

I'm a pro at those boosters. ya buddy.

 

[Turbocharged400sbc]

gonna have to do some modifying of the coolant flow for the heater core...yay

prob end up routing the pressure side to the npt plugged port that just behind the TV cable in this pic

 

[Turbocharged400sbc]

this piece of shit should prob be moved to the 3800 section of awesomeness

edit god damn james

 

[Turbocharged400sbc]

well the PS shit is done...only the other half of the lines remain and those are easy, gotta pick up some 180* hose bends for the heater return pipe and the PS pump sump
im gonna see about grabbing a V6 bellhousing 4l60 dipstick tube from the junkyard but if it comes down to it im just gonna shorten the SBC 700r4 dipstick and tube.
and yes i bent conduit for the custom heater return pipe

the volvo PS reservoir couldnt have worked out better....plenty of hood clearance and is just a hair higher than the pump inlet...

 

[Handsome Jesus]

looking good mr james

 

[TommyGloves]

 

[02BlueGT]

 

[Turbocharged400sbc]

ya need to stop over next time your free from the ball and chain

i just blew a fair bit o money on it today

 

[Turbocharged400sbc]

added some paint and getting much closer to final assembly and finishing the exhaust.
im using the stock TB im gonna drill the 2 bolt patern in the m62 and be done with it...filter will be panyhose or a tshirt clamped across the opening

PS bracket turned out great as did the res mount... you can see the new hot coolant feed to the heatercore ECT sits on the other side of that T below the TB area.
i have my new fuel line routing figured out but ill probably rig it with EFI hose

 

[10sec]

Put a cam in it, kthx.

 

[Turbocharged400sbc]

when my lathe is running and i can make a SI/SII hybrid cam blank and get it ground....i will

 

[Frank Dukes]

update?

 

[Turbocharged400sbc]

wher'd it go?!? honest question....should i bother with cleaning and painting the rusty crap or just leave it with its current patina and just wipe it down?

nothing like huffing paint haha
that white Kmember is reallly white

 

[Bob Kazamakis]

I say leave it as is.