3800 Online database to post your scan

[imported_Diavolo]

Hey, (cliffnotes at bottom)

I have noticed a lot of problems when people post there scans on forums, they are always hard to read and such.

I have created an easy solution. I have set up an online database where you can submit your .CSV scans and then view them in an easy to read table.

You can also view other people's scans, making it easy for people to get help with there scan (i.e. IF I needed help, I would ask someone to look at my scan and tell them my user name and the scan name, they can then go to the database and find the scan and view it in a easy to read table.)

Check it out at http://www.amoxsoft.com/mike

Let me know if this is something useful or not, I just did this in a few hours so it isn't very pretty but there doesn't seem to be any bugs (of course, I was the only one trying it out).

----------------CLIFF NOTES---------------
go to http://www.amoxsoft.com/mike

Click to read more...

 

[imported_Diavolo]

subscribing to post :lame: :linksucks: :blahblah:

 

[syP]

its VERY useful... u guys just gotta check it out.

 

[dole21]

need to scan my car again then...cause when i try to convert my autotap file over its all screwed up and hard to read...

 

[imported_Diavolo]

need to scan my car again then...cause when i try to convert my autotap file over its all screwed up and hard to read...

Are they converted into a .csv file?

03/30/00 08:25a
2
Scan time,KR,IAT,IGN,LFT1,MAF,MPH,O2L,B,RPM,TPS
mS,DEG,DEGF,DEG,PCT,LB/MN,MPH,mV,Err,RPM,PCT
Milliseconds to complete this scan,Knock retard,Intake air temp,Ignition timing,Long-term fuel trim - dr's side,Mass air flow,Vehicle speed,O2 sensor - driver's side,Err,Engine speed,Throttle position sensor
660,0.00,77.0,34.0,-2.34,1.90,18.0,550,0.00,1426,6.3
310,0.00,77.0,35.0,-2.34,1.90,18.0,70,0.00,1458,6.3
330,0.00,77.0,35.0,-2.34,1.92,18.0,80,0.00,1484,9.0
310,0.00,77.0,17.0,-1.56,6.83,19.3,825,0.00,2148,41.6
310,0.00,77.0,16.0,0.00,10.99,21.1,855,0.00,2849,75.7
310,0.00,77.0,17.0,1.56,12.42,23.0,880,0.00,3135,100.0
310,0.00,77.0,10.0,1.56,14.09,24.9,885,0.00,3440,100.0
310,0.00,77.0,17.0,1.56,15.00,27.3,890,0.00,3581,100.0
310,0.00,77.0,17.0,1.56,15.12,29.8,890,0.00,3755,100.0
320,0.00,77.0,17.0,1.56,16.05,32.3,890,0.00,4020,100.0
310,0.00,77.0,17.0,1.56,17.68,35.4,890,0.00,4283,100.0
310,0.00,77.0,17.0,1.56,18.44,37.3,895,0.00,4551,100.0
310,0.00,77.0,16.0,1.56,19.49,40.4,885,0.00,4819,100.0
310,0.00,77.0,17.0,1.56,20.57,42.3,890,0.00,5041,100.0
310,0.00,77.0,17.0,1.56,21.42,45.4,890,0.00,5264,100.0
310,0.00,77.0,17.0,1.56,22.56,47.2,890,0.00,5553,100.0
330,0.00,77.0,13.0,1.56,21.88,49.7,880,0.00,4615,100.0

That is an example of a scan in a CSV file.

If that is your problem, go to that webpage and load it in. It will be useful for you then

 

[imported_Diavolo]

no comments? Please just say It sucks or It is a good idea. If it sucks, I am not going to spend time making it look pretty.

 

[ThaLord]

awesome idea, if you need a place to host it.. I will give you the space.. free of charge..

John

 

[imported_Diavolo]

John, you got pm

 

[dole21]

ok...

I did 4 runs with my autotap today and posted it on the site..


but I can't figure out why it keeps doing the multiple time start one...


the name of my scans are my ICCU setting..IDLE CRUISING WOT

so...even when I increased my WOT mixture from 104 to 108 I seemed to lose some knock...but the LTFT stayed at 12.8%...

I'm lost and if anyone could give me some help on tuning I'd appreciate it...

Thanks all in advance.

 

[imported_Diavolo]

The numbers look good. At WOT, don't worry about the LFT's. use the LFT's during idle and cruise, but at WOT, it locks in and then you need to use the 02's to tune.

What are your mods?

 

[dole21]

My mods are

1X Cam
105 lb spring
3.2 Pulley
3"Downpipe catback with magnaflows
Running 104's gapped @ 58
FWI(9 inch cone)
DHP

Am I at the point where I should switch plugs? Try 103's? or maybe a different gap? I know nothing on which way I should switch a gap or what is recommended, someone a while ago told me to do that gap...

My DHP is not currently setup to change the timing..I'll get to that someday also. and I know headers are needed h34r:

 

[imported_Diavolo]

NEW LINK*******************

www.ilgpc.com/scan

Thanks John for setting that up